Skip to content
HOW TO MAKE EARL GREY TEA SOAP

HOW TO MAKE EARL GREY TEA SOAP

Here is a simple guide showing how to make Earl Grey Tea Soap

Supplies 

 

  • Crystal Shea & Crystal Goats Milk
  • Loose leaf Earl Grey Tea Black tea bags
  • Soap molds – Modern molds plastic/silicone,for this tutorial our expert used vintage Jello tins.
  • Isopropyl Alcohol spray
  • Container for melting
  • Spoon 

  • STEP 1 Cut a couple large chunks from the package of soap, and chop them into smallish cubes.

    STEP 2 Dump all the cubes of soap into a microwave-safe container. One with a pouring spout is ideal, but you could do this in a bowl or mug if that’s all you have. Microwave for 30 seconds, and then stir it thoroughly with the stirrer. If you still have any unmelted chunks, continue to melt in ten-second intervals, stirring after each. Careful – this can get very hot!

     STEP 3 Carefully pour the melted soap into your mold, filling the mold 1/2 to 2/3, depending on your preference. The more you fill it in this step, the bigger the white section of your soap will be.

     

    STEP 4 Throw the remaining melted soap back in the microwave for 10-20 seconds to get it piping hot and liquidy again. Drop a couple black tea (English breakfast, Irish breakfast, Early grey, etc.) into the mixture, and let them steep for about 30 seconds. Carefully use the back of the spoon to squeeze the tea bags against the side of the container, extracting nice, dark tea-stained soap. Mix it up thoroughly to spread the color around evenly.

    STEP 5 Once the white soap from Step 3 has firmed up a bit on top, it’s time to pour the tea layer. First spray the white soap with a bit of the Isopropyl Alcohol Spray to help the layers stick together. Pour it over the back of a spoon, like in the picture below. This will allow it to pour in gently and not mix too much with the white layer. Pour it close to the top, but leave enough room for the tea. You can take a look at the picture below to give you a better idea.

    STEP 6 Immediately sprinkle a really generous helping of your loose leaf Earl Grey tea all over the top of the melted soap. Completely cover it, using way more tea than you need. You can just tap off the excess when it’s all firmed up.

     STEP 7 Allow the soap to harden for several hours, minimum 2hours, before popping it out of the mold. Then, you can just tap off the excess tea!

     

    STEP 8 Finish product can be wrapped and give as a gift or use it in the next time you have a shower.  

     

    Previous article Scented Impression
    Next article DIY Gift Guide: Himalayan Salt and Lavender Oil Bath Soak

    Register for back in stock notifications

    For [productTitle] [variantTitle]
    Opt-in for marketing newsletters. Privacy policy.

    Thank you for your interest in this product. We will let you know as soon as this becomes available.

    An error occured while processing your request, please try again later.

    You have already subscribed to this product.

    This product has a maximum order limit of <qty>. Please contact <phone> or email as at <email> for bulk orders

    Please call [phone] to obtain a bulk shipping quote

    403

    Access Denied

    You do not have permission to view this page

    Please contact customerservice@candlesupply.com.au for assistance or refresh the page to retry. If you are using a VPN please disable it.

    ES,CZ,IR,UA,PL,RU
    none
    none
    154.95.36.199,45.94.47.66,45.87.249.143,185.199.228.220,45.13.184.226,45.13.184.148
    none
    candle-supply-nz-dev.myshopify.com